AMX NMX-ENC-1115-WP-BL (FGN1115-WP-BL) Wallplate Encoder - Black

Description

AMX NMX-ENC-1115-WP-BL (FGN1115-WP-BL) Wallplate Encoder - unit open, never used. Missing screws and ground cable. Excellent condition.
NMX-ENC-N1115-WP Wallplate Encoder
Minimal Proprietary Compression Video Over IP N1115 MPC Decor Style Wallplate Encoder with KVM
The N1000 Series Encoders and Decoders are an affordable local AV-over-IP switching solution that packetizes video into a minimally compressed IP format that provides excellent video quality at low latencies. This compression is perfect for point-to-point video distribution, small 2x1 switching applications, and larger switching applications (for example, 32x32), all using off-the-shelf layer-3 network switches.
The NMX-ENC-N1115-WP provides the excellent encoding capabilities of the NMX-ENC-N1133 in a 2-gang wallplate format. This encoder can be easily mounted in a wall, lectern, or floor box using a standard 2-gang US back box, and connected to power and Ethernet using only a single category cable.
Common Applications
The NMX-ENC-N1115 is the perfect solution for any application and video matrix smaller than 32x32. Common applications include conference rooms, huddle spaces, and lecterns (inside or adjacent-to)
Features
Sub-Frame Latency – Combined encode and decode latency of 10 ms at 60 fps.
Minimal Proprietary Compression (MPC) – Visually lossless MPC algorithm applied applied to all resolutions
Wallplate Form Factor – Fits conveniently into a 2-gang US back box for easy installation in a wall, floor, or lectern.
Power Over Ethernet (PoE) – PoE eliminates the need for power supply
Unmatched Flexibility – Build point-to-point links, simple 2x1 switches, or cost-effective matrices up to 32x32.
Separate Inputs – Separate HDMI and VGA input connectors on the encoder
Specifications
Video
Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
Analog Video Input: HD-15 VGA, Component*
Video Output: Video Output
Formats: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
Progressive Input Resolutions
Supports most common HD up to 1920x1200.
Interlaced Input Resolutions
Supports 1080i60.
Analog Input Resolutions
NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
Supports most common HD up to 1920x1200.
Output Resolutions: Matched to inputs.
Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
NOTE: The N1115-WP does not accept Composite or S-Video (YC).
Color Space: 4:2:2
*These signal types are supported through a passive adapter.
Audio
Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
Output Signal Types: Ethernet
Analog Audio Format: 8ch PCM, Stereo 2-channel
Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
Latency
Latency: 10 ms at 60 fps
Bandwidth: 840 Mb/s (varies with resolution)
Note: This is the combined encode plus decode latency. Total latency from source to screen will also include any network latency.
Note: Scaling adds one frame of latency (17ms at 60fps).
Communications
Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
HDMI: HDCP, EDID management
Ports
P0:
8-wire RJ45 female
10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port
Provides the network connection, network AV video, and power to the Encoders and Decoders
HDMI IN: HDMI video input
VGA IN: DB15 analog input
USB IN - Host: USB-B host input
USB IN - Maintenance: USB-Mini maintenance input
Controls and Indicators - Front Panel
RESET Button:
Recessed pushbutton
Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
AUDIO LED: On (green) when audio is transmitting.
ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.
DIGITAL VIDEO LED: On (green) when video source is available and transmitting
HDCP LED: On (green) when the source is using HDCP
STREAM LED: On (green) when the unit is streaming video
STATUS LED: Flashing (green) when the unit is active.
LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.
Power Supply
Power over Ethernet
Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1)
Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.
Note: In order for the unit to receive Power over Ethernet (PoE), it must be connected to a switch or other equipment that has a PoE PSE (Power Sourcing Equipment) port. Warning: Do not run wiring that is connected to a PoE PSE port outside of the building where the PSE resides. It is for intra-building use only.
Environmental
Temperature (Operating): 32° to 104°F (0° to 40°C)
Temperature (Storage): -22° to 158°F (-30° to 70°C)
Humidity (Operating): 10% to 90% RH (non-condensing)
Humidity (Storage): 0% to 90% RH (non-condensing)
Heat Dissipation: Up to ~26 BTU/hr
General
Dimensions (HWD): 4.06" x 3.5" x 2.25" (10.31 cm x 8.84 cm x 5.72 cm)
Weight: .75 lb (0.34 kg)
Airflow: Natural convection via vent openings on front, back, and top
Installation
Mounts onto standard 2 gang US back boxes
Mounts into standard décor style wallplates (not included)
Regulatory Compliance: FCC, CE, and NTRL
Recommended Accessories
Compatible with NMX-ENC-N1222, NMX-ENC-N1233, NMX-ENC-N1512, and NMX-NVR-N6123
PS-POE-AT-TC High-Power PoE Injector, 802.3AT Compliant FG423-84)